1. PBAP/PCE/SGSIT/OFFS/BV-01-C
1. 测试项说明：
Please initiate a GATT connection over BR/EDR to the PTS.
Description: Verify that the Implementation Under Test (IUT) can initiate GATT connect request over BR/EDR to PTS.
测试项名称：
Please initiate a GATT connection over BR/EDR to the PTS.
测试项描述：
验证被测设备（IUT）是否能够通过 BR/EDR（经典蓝牙）主动发起 GATT 连接请求到 PTS（Protocol Test System）。
2. 基本概念
1. 什么是 GATT？
GATT（Generic Attribute Profile）是 BLE（低功耗蓝牙）中用于设备之间传输数据的通用协议，基于 ATT（Attribute Protocol）实现。
2. 什么是 BR/EDR？
BR/EDR 是“Basic Rate / Enhanced Data Rate”的缩写，也就是经典蓝牙。传统上，GATT 运行于 BLE（即 LE）上，但从 Bluetooth Core v4.1 起，GATT 也可以工作在 BR/EDR 上。
3. 为什么要测试 GATT over BR/EDR？
虽然 GATT 多用于 BLE，但有些场景或设备（比如某些老设备或兼容设备）需要在经典蓝牙上复用 GATT 协议。因此，Bluetooth SIG 定义了这个测试项来确保 IUT 能在 BR/EDR 上传输 GATT 协议。
3. 测试目的
验证被测设备（IUT）是否能够：
- 使用 BR/EDR（经典蓝牙）连接到 PTS；
- 正确发起 GATT 连接请求（如发送 MTU 交换请求）；
- 在 BR/EDR 信道上使用 ATT 协议通信；
- 满足 GATT over BREDR 的规范要求。
4. 测试流程简述
| 步骤 | 动作 |
|---|---|
| 1 | IUT 与 PTS 建立配对（通过经典蓝牙） |
| 2 | IUT 执行 SDP 查询，找到 PTS 提供的 GATT 服务（UUID: 0x1801） |
| 3 | IUT 通过 BR/EDR 打开 L2CAP 固定信道（通常为 0x0004） |
| 4 | IUT 发送 ATT 请求（如 Exchange MTU Request） |
| 5 | PTS 响应，连接建立成功 |
| 6 | 记录测试结果（通过 / 失败） |
5. 测试重点与注意事项
| 项目 | 要点 |
|---|---|
| ✅ 连接方式 | 必须是 BR/EDR（经典蓝牙），不能使用 BLE |
| ✅ SDP 查询 | IUT 应能找到 GATT 服务的 SDP 记录（Generic Attribute Profile） |
| ✅ L2CAP 信道 | 使用固定信道 0x0004 建立 ATT 通道 |
| ✅ ATT 层 | IUT 应发送标准的 GATT 请求，如 MTU 交换、服务发现等 |
| ❌ 错误示范 | 如果 IUT 走了 BLE 的 GATT 路径，则测试会被判为失败 |
| ⚠️ 蓝牙协议栈支持 | 部分蓝牙协议栈（如 Android、BlueZ）默认不支持 GATT over BR/EDR，需要手动适配或扩展 |
6. 常见失败原因（SERR）
| 问题 | 原因 |
|---|---|
| GATT 请求未发出 | IUT 没有正确连接或协议栈不支持 |
| 使用了 LE 连接 | 测试要求使用经典蓝牙，不能用 LE |
| SDP 查询失败 | 未找到 GATT 服务 UUID |
| L2CAP 信道错误 | 未使用 0x0004 或配置不当 |
| 没有发送 ATT 数据 | 上层未触发 GATT 请求流程 |
7. 调试建议
抓包工具：使用 Ellisys 或 Frontline 观察 HCI 层是否通过 BR/EDR 连接；
确认 ACL 链路类型：应为 classic BR ACL 而非 LE；
查看 SDP 记录：确认 PTS 是否发布了 GATT 服务 UUID；
打印日志：开启协议栈日志，如 BlueZ 可查看
btmon，Android 可用logcat。
8. 总结
本测试项的关键是：
确保设备在 BR/EDR 上传输 GATT 协议，并能主动连接并通信。
由于很多现代蓝牙协议栈默认只支持 GATT over LE，若设备原生不支持，需要自行扩展协议栈才能通过此项测试。
2. 真实车机侧案例
我们 IUT 测试对象是车机。 android 的协议栈不支持，默认不支持 GATT over BR/EDR。 看到这里， 是不是有点担心。 如果要过这一项测试，是不是要 人为改代码， 来适配 GATT over BR/EDR。 我实际测试了一下。直接是可以通过的。
我这里 记录一下 车机侧的 btsnoop 日志。 看一下为何在协议栈不支持 GATT over BR/EDR 的情况下。还能测试通过。
- 发现只有 sdp 的流程， 没有后续 连接 pbap 的流程。
- 那我们重点看一下， 车机发起 sdp 后， pts. 回复的内容。
# 车机向 pts 查询 Phonebook Access Server
975 2025-04-25 17:53:59.966042 22:22:96:de:b1:39 (leo 8295 chan) Vencer_f4:b1:83 (PTS-PBAP-B183) SDP 29 Sent Service Search Attribute Request : Phonebook Access Server: Attribute Range (0x0000 - 0xffff)
# pts 回复如下：
980 2025-04-25 17:53:59.991359 Vencer_f4:b1:83 (PTS-PBAP-B183) 22:22:96:de:b1:39 (leo 8295 chan) SDP 19 Rcvd Service Search Attribute Response
Bluetooth SDP Protocol
PDU: Service Search Attribute Response (0x07)
Transaction Id: 0x0000
Parameter Length: 5
Attribute List Byte Count: 2
Attribute Lists [count = 0]
Data Element: Sequence uint8 0 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 0
Data Value: MISSING # 这里看到 pts 返回的 数据内容是空的。
Continuation State: no (00)
而我们 协议栈判断到， pts 的 返回的 sdp record 是空的后， 就没有继续发起 pbap 的连接。
04-25 17:53:59.140092 9393 9488 D PbapClientStateMachine: mCchPathUsed: false
04-25 17:53:59.140338 9393 9720 I PbapClientStateMachine: Enter Connecting: -2
04-25 17:53:59.140520 9393 9720 D PbapClientStateMachine: Connection state 00:1B:DC:F4:B1:83: 0->1
04-25 17:54:00.009577 9393 9393 I PbapClientStateMachine: onReceiveandroid.bluetooth.device.action.SDP_RECORD
04-25 17:54:00.009815 9393 9393 I PbapClientStateMachine: Received UUID: 0000112f-0000-1000-8000-00805f9b34fb
04-25 17:54:00.009968 9393 9393 I PbapClientStateMachine: expected UUID: 0000112f-0000-1000-8000-00805f9b34fb
// 直接返回错误了
04-25 17:54:00.010025 9393 9393 E PbapClientStateMachine: SDP Record fetched status isn't ok - Ignore. status=1
// android/app/src/com/android/bluetooth/pbapclient/PbapClientStateMachine.java
private class SDPBroadcastReceiver extends BroadcastReceiver {
@Override
public void onReceive(Context context, Intent intent) {
String action = intent.getAction();
if (DBG) {
Log.i(TAG, "onReceive" + action);
}
if (action.equals(BluetoothDevice.ACTION_SDP_RECORD)) {
BluetoothDevice device =
intent.getParcelableExtra(BluetoothDevice.EXTRA_DEVICE);
BluetoothDevice sm_device = getDevice();
if (sm_device !=null) {
if (!device.equals(getDevice())) {
Log.w(TAG, "SDP Record fetched for different device - Ignore");
return;
}
} else {
Log.d(TAG, "SDP Record get device is null - Ignore");
return;
}
ParcelUuid uuid = intent.getParcelableExtra(BluetoothDevice.EXTRA_UUID);
if (DBG) {
Log.i(TAG, "Received UUID: " + uuid.toString());
Log.i(TAG, "expected UUID: " + BluetoothUuid.PBAP_PSE.toString());
}
int search_status= intent.getIntExtra(BluetoothDevice.EXTRA_SDP_SEARCH_STATUS,-1);
if (search_status != AbstractionLayer.BT_STATUS_SUCCESS) {
// 直接在这里返回退出了。
Log.e(TAG, "SDP Record fetched status isn't ok - Ignore. status="+search_status);
return;
}
if (uuid.equals(BluetoothUuid.PBAP_PSE)) {
// 正常的逻辑，应该走到这里， sdp 完成后，会继续触发 后续连接操作。
sendMessage(MSG_SDP_COMPLETE,
intent.getParcelableExtra(BluetoothDevice.EXTRA_SDP_RECORD));
}
}
}
}
}
发现这一项， 由于 pts 返回的 sdp record 状态有问题。 后续车机干脆没有发起 pbap 的连接。 直接 pts软件 pass 了。
3. 正确的 sdp
这里对比分享一个 正常，可以建立 pbap 情况下的， sdp 的内容。
# 车机主动发起 sdp 请求
846 2025-04-25 14:08:32.468449 22:22:96:de:b1:39 (leo 8295 chan) Vencer_f4:b1:83 (PTS-PBAP-B183) SDP 29 Sent Service Search Attribute Request : Phonebook Access Server: Attribute Range (0x0000 - 0xffff)
# pts 回复正确的 sdp record
849 2025-04-25 14:08:32.507350 Vencer_f4:b1:83 (PTS-PBAP-B183) 22:22:96:de:b1:39 (leo 8295 chan) SDP 255 Rcvd Service Search Attribute Response
Bluetooth SDP Protocol
PDU: Service Search Attribute Response (0x07)
Transaction Id: 0x0000
Parameter Length: 241
Attribute List Byte Count: 238
Attribute Lists [count = 2]
Data Element: Sequence uint8 236 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 236
Data Value
Attribute List [count = 10] (Phonebook Access Server)
Data Element: Sequence uint8 119 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 119
Data Value
Service Attribute: Service Record Handle (0x0), value = 0x00090021 (589857)
Attribute ID: Service Record Handle
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Service Record Handle (0x0000)
Value
Data Element: Unsigned Integer 4 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .010 = Data Element Size: 4 bytes (2)
Data Value
Service Record Handle: 0x00090021
Service Attribute: Service Class ID List (0x1), value = Phonebook Access Server
Attribute ID: Service Class ID List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Service Class ID List (0x0001)
Value
Data Element: Sequence uint8 3 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 3
Data Value
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: Phonebook Access Server (0x112f)
Service Attribute: Protocol Descriptor List (0x4), value = L2CAP -> RFCOMM:2 -> OBEX
Attribute ID: Protocol Descriptor List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Protocol Descriptor List (0x0004)
Value
Data Element: Sequence uint8 17 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 17
Data Value
Protocol #1: L2CAP
Data Element: Sequence uint8 3 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 3
Data Value
Protocol Entry: L2CAP
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: L2CAP (0x0100)
Protocol #2: RFCOMM, RFCOMM Channel: 2
Data Element: Sequence uint8 5 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 5
Data Value
Protocol Entry: RFCOMM, RFCOMM Channel: 2
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: RFCOMM (0x0003)
Data Element: Unsigned Integer 1 byte (0 bytes if Nil)
0000 1... = Data Element Type: Unsigned Integer (1)
.... .000 = Data Element Size: 1 byte (0 bytes if Nil) (0)
Data Value
RFCOMM Channel: 2 (0x02)
Protocol #3: OBEX
Data Element: Sequence uint8 3 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 3
Data Value
Protocol Entry: OBEX
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: OBEX (0x0008)
Service Attribute: Browse Group List (0x5), value = Public Browse Group
Attribute ID: Browse Group List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Browse Group List (0x0005)
Value
Data Element: Sequence uint8 3 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 3
Data Value
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: Public Browse Group (0x1002)
Service Attribute: Language Base Attribute ID List (0x6), value = (Lang: en, Encoding: UTF-8, Attribute Base: 0x0100)
Attribute ID: Language Base Attribute ID List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Language Base Attribute ID List (0x0006)
Value
Data Element: Sequence uint8 9 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 9
Data Value
Language #1: Lang: en, Encoding: UTF-8, Attribute Base: 0x0100
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Language Code: en
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Language Encoding: UTF-8 (106)
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute Base: 0x0100
Service Attribute: Bluetooth Profile Descriptor List (0x9), value = Phonebook Access Profile 1.2
Attribute ID: Bluetooth Profile Descriptor List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Bluetooth Profile Descriptor List (0x0009)
Value
Data Element: Sequence uint8 8 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 8
Data Value
Data Element: Sequence uint8 6 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 6
Data Value
Profile Descriptor List #1: Phonebook Access Profile, Version 1.2
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: Phonebook Access Profile (0x1130)
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Protocol Version: 0x0102
Service Attribute: Service Name (0x100), value = Phonebook Acccess PSE
Attribute ID: Service Name
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Service Name (0x0100)
Value
Data Element: Text string uint8 22 bytes
0010 0... = Data Element Type: Text string (4)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 22
Data Value
Service Name: Phonebook Acccess PSE
Service Attribute: (PBAP) GOEP L2CAP PSM (0x200), value = 4101 (0x1005)
Attribute ID: GOEP L2CAP PSM
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: GOEP L2CAP PSM (0x0200)
Value
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
GOEP L2CAP PSM: 4101 (0x1005)
Service Attribute: (PBAP) Supported Repositories (0x314), value = LocalPhonebook SIM SpeedDial Favourites
Attribute ID: Supported Repositories
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Supported Repositories (0x0314)
Value
Data Element: Unsigned Integer 1 byte (0 bytes if Nil)
0000 1... = Data Element Type: Unsigned Integer (1)
.... .000 = Data Element Size: 1 byte (0 bytes if Nil) (0)
Data Value
Supported Repositories: 0x0f
0000 .... = Reserved: 0x0
.... 1... = Favourites: True
.... .1.. = Speed Dial: True
.... ..1. = SIM Card: True
.... ...1 = Local Phonebook: True
Service Attribute: (PBAP) Supported Features (0x317), value =
Attribute ID: Supported Features
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Supported Features (0x0317)
Value
Data Element: Unsigned Integer 4 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .010 = Data Element Size: 4 bytes (2)
Data Value
Supported Features: 0x00000000
0000 0000 0000 0000 0000 00.. .... .... = Reserved: 0x000000
.... .... .... .... .... ..0. .... .... = Default Contact Image Format: False
.... .... .... .... .... ...0 .... .... = Contact Referencing: False
.... .... .... .... .... .... 0... .... = X-BT-UID vCard Property: False
.... .... .... .... .... .... .0.. .... = X-BT-UCI vCard Property: False
.... .... .... .... .... .... ..0. .... = Enhanced Missed Calls: False
.... .... .... .... .... .... ...0 .... = vCard Selecting: False
.... .... .... .... .... .... .... 0... = Folder Version Counters: False
.... .... .... .... .... .... .... .0.. = Database Identifier: False
.... .... .... .... .... .... .... ..0. = Browsing: False
.... .... .... .... .... .... .... ...0 = Download: False
Attribute List [count = 9] (Phonebook Access Server)
Data Element: Sequence uint8 113 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 113
Data Value
Service Attribute: Service Record Handle (0x0), value = 0x00090063 (589923)
Attribute ID: Service Record Handle
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Service Record Handle (0x0000)
Value
Data Element: Unsigned Integer 4 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .010 = Data Element Size: 4 bytes (2)
Data Value
Service Record Handle: 0x00090063
Service Attribute: Service Class ID List (0x1), value = Phonebook Access Server
Attribute ID: Service Class ID List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Service Class ID List (0x0001)
Value
Data Element: Sequence uint8 3 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 3
Data Value
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: Phonebook Access Server (0x112f)
Service Attribute: Protocol Descriptor List (0x4), value = L2CAP -> RFCOMM:2 -> OBEX
Attribute ID: Protocol Descriptor List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Protocol Descriptor List (0x0004)
Value
Data Element: Sequence uint8 17 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 17
Data Value
Protocol #1: L2CAP
Data Element: Sequence uint8 3 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 3
Data Value
Protocol Entry: L2CAP
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: L2CAP (0x0100)
Protocol #2: RFCOMM, RFCOMM Channel: 2
Data Element: Sequence uint8 5 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 5
Data Value
Protocol Entry: RFCOMM, RFCOMM Channel: 2
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: RFCOMM (0x0003)
Data Element: Unsigned Integer 1 byte (0 bytes if Nil)
0000 1... = Data Element Type: Unsigned Integer (1)
.... .000 = Data Element Size: 1 byte (0 bytes if Nil) (0)
Data Value
RFCOMM Channel: 2 (0x02)
Protocol #3: OBEX
Data Element: Sequence uint8 3 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 3
Data Value
Protocol Entry: OBEX
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: OBEX (0x0008)
Service Attribute: Browse Group List (0x5), value = Public Browse Group
Attribute ID: Browse Group List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Browse Group List (0x0005)
Value
Data Element: Sequence uint8 3 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 3
Data Value
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: Public Browse Group (0x1002)
Service Attribute: Language Base Attribute ID List (0x6), value = (Lang: en, Encoding: UTF-8, Attribute Base: 0x0100)
Attribute ID: Language Base Attribute ID List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Language Base Attribute ID List (0x0006)
Value
Data Element: Sequence uint8 9 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 9
Data Value
Language #1: Lang: en, Encoding: UTF-8, Attribute Base: 0x0100
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Language Code: en
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Language Encoding: UTF-8 (106)
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute Base: 0x0100
Service Attribute: Bluetooth Profile Descriptor List (0x9), value = Phonebook Access Profile 1.0
Attribute ID: Bluetooth Profile Descriptor List
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Bluetooth Profile Descriptor List (0x0009)
Value
Data Element: Sequence uint8 8 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 8
Data Value
Data Element: Sequence uint8 6 bytes
0011 0... = Data Element Type: Sequence (6)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 6
Data Value
Profile Descriptor List #1: Phonebook Access Profile, Version 1.0
Data Element: UUID 2 bytes
0001 1... = Data Element Type: UUID (3)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Value: UUID: Phonebook Access Profile (0x1130)
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Protocol Version: 0x0100
Service Attribute: Service Name (0x100), value = Phonebook Acccess PSE
Attribute ID: Service Name
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Service Name (0x0100)
Value
Data Element: Text string uint8 22 bytes
0010 0... = Data Element Type: Text string (4)
.... .101 = Data Element Size: uint8 (5)
Data Element Var Size: 22
Data Value
Service Name: Phonebook Acccess PSE
Service Attribute: (PBAP) Supported Repositories (0x314), value = LocalPhonebook SIM SpeedDial Favourites
Attribute ID: Supported Repositories
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Supported Repositories (0x0314)
Value
Data Element: Unsigned Integer 1 byte (0 bytes if Nil)
0000 1... = Data Element Type: Unsigned Integer (1)
.... .000 = Data Element Size: 1 byte (0 bytes if Nil) (0)
Data Value
Supported Repositories: 0x0f
0000 .... = Reserved: 0x0
.... 1... = Favourites: True
.... .1.. = Speed Dial: True
.... ..1. = SIM Card: True
.... ...1 = Local Phonebook: True
Service Attribute: (PBAP) Supported Features (0x317), value =
Attribute ID: Supported Features
Data Element: Unsigned Integer 2 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .001 = Data Element Size: 2 bytes (1)
Data Value
Attribute ID: Supported Features (0x0317)
Value
Data Element: Unsigned Integer 4 bytes
0000 1... = Data Element Type: Unsigned Integer (1)
.... .010 = Data Element Size: 4 bytes (2)
Data Value
Supported Features: 0x00000000
0000 0000 0000 0000 0000 00.. .... .... = Reserved: 0x000000
.... .... .... .... .... ..0. .... .... = Default Contact Image Format: False
.... .... .... .... .... ...0 .... .... = Contact Referencing: False
.... .... .... .... .... .... 0... .... = X-BT-UID vCard Property: False
.... .... .... .... .... .... .0.. .... = X-BT-UCI vCard Property: False
.... .... .... .... .... .... ..0. .... = Enhanced Missed Calls: False
.... .... .... .... .... .... ...0 .... = vCard Selecting: False
.... .... .... .... .... .... .... 0... = Folder Version Counters: False
.... .... .... .... .... .... .... .0.. = Database Identifier: False
.... .... .... .... .... .... .... ..0. = Browsing: False
.... .... .... .... .... .... .... ...0 = Download: False
Continuation State: no (00)